Experimental research on mechanical, material, and metallurgical properties of Inconel 600: Application in elevated temperature environment
DOI:
https://doi.org/10.62676/jdaf.2024.2.1.30Keywords:
Inconel 600 , Fatigue , Creep, Mechanical properties , High temperatureAbstract
Du to high strength and toughness, high oxidation resistance, and high ductility, the Inconel 600 alloy is an ideal choice for the components used in combined heat and power turbines. Therefore, in this paper, the authors conducted experimental tests to better underestand the mechanical behavior of superalloys Inconel 600. The experiments included tensile, fatigue, and creep tests. The material deformation and stress-strain behavior were measured. In addition the yield strength, ultimate tensile strength, elongation, and modulus of elasticity were captured. By illustrating the engineering and true stress-strain curves the Ramberg-Osgood relation were extracted. As a result of fatigue test, the relationship between strain amplitude and the number of cycles to failure for specimens were obtained. The creep tests were conducted at a constant temperature of 650℃. The strain-time data were collected, and the resulting creep strain-time curve were plotted for smooth samples under their respective stress conditions.
REFERENCES
- G. Becerra, M.R.B. Alvarez, V.H.L Morelos, A. Ruiz. Creep behavior and microstructural characterization of Inconel-625/Inconel-600 welded joint. MRS Adv. 8, (2023) 1217–1223, https://doi.org/10.1557/s43580-023-00662-7.
- Baig, S.H.I. Jaffery, M.A. Khan, M. Alruqi, Statistical analysis of surface roughness, burr formation and tool wear in high speed micro milling of Inconel 600 alloy under cryogenic, wet and dry conditions. Micromachines 14(1) 2023, 13. https://doi.org/10.3390/mi14010013.
- Nanaware, S. Pawar, M. Ramachandran. Mechanical characterization of nickel alloys on turbine blades. REST J.E.M.M., 1(1) (2015), 15–19.
- D. Kwon, D.K. Park, S.W. Woo, D.H. Yoon, I. Chung. A study on fretting fatigue life for the Inconel alloy 600 at high temperature. Nucl. Eng. Des. 240 (2010) 2521–2527. https://doi.org/10.1016/j.nucengdes.2010.05.013.
- Gajalappa, A. Krishnaiah, K.B. Kumar, Eswaranna, K.K. Saxena, P. Goyal. Flow behaviour kinetics of Inconel 600 superalloy under hot deformation using gleeble 3800. Mater. Today: Proc. 45 (2021) 5320–5322. https://doi.org/10.1016/j.matpr.2021.01.909.
- Y. Wu, P.H. Sun, F.J. Zhu, S.C. Wang, W.R. Wang, C.C. Wang, C.H. Chiu. Tensile flow behavior in Inconel 600 alloy sheet at elevated temperatures. Procedia Eng. 36 (2012) 114–120. https://doi.org/10.1016/j.proeng.2012.03.018.
- Xu, S. Wang, X. Tang, Y. Li, J. Yang, J. Li, Y. Zhang. Corrosion mechanism of Inconel 600 in oxidizing supercritical aqueous systems containing multiple salts. Eng. Chem. Res. 58(51) (2019) 23046–23056. https://doi.org/10.1021/acs.iecr.9b04527.
- S. Al-Rubaie, L.B. Godefroid, J.A.M. Lopes. Statistical modeling of fatigue crack growth rate in Inconel alloy 600. Int. J. Fatigue 29 (2007) 931–940. https://doi.org/10.1016/j.ijfatigue.2006.07.013.
- Y. Wu, F.J. Zhu, S.C. Wang, W.R. Wang, C.C. Wang, C.H. Chiu. Hot deformation characteristics and strain-dependent constitutive analysis of Inconel 600 superalloy. J. Mater. Sci. 47 (2012) 3971–3981. https://doi.org/10.1007/s10853-012-6250-4.
- A. Khafri, N. Golarzi. Forming behavior and workability of Hastelloy X superalloy during hot deformation. Mater. Sci. Eng. A 486 (2008) 641–647. https://dx.doi.org/10.1016/j.msea.2007.11.059.
- T.W.K. Fahmi, K.R. Kashyzadeh, S. Ghorbani. A comprehensive review on mechanical failures cause vibration in the gas turbine of combined cycle power plants. Engineering Failure Analysis 134 (2022) 106094. https://doi.org/10.1016/j.engfailanal.2022.106094.
- J. Li, K.L. Lin. Strengthening of Inconel 600 alloy with electric current stressing. MTLA 27 (2023) 101666.
https://doi.org/10.1016/j.mtla.2022.101666.
- T. Kim, Y.S. Kim. The effect of the static load in the UNSM process on the corrosion properties of alloy 600. Materials 12 (2019) 3165. https://doi.org/10.3390/ma12193165.
- Kuzmanov, B. Borisov, I. Muhtarov. Tensile testing of Inconel 600 wire at high temperatures. IOP Conf. Ser.: Mater. Sci. Eng. 878 (2020) 012057.
https://doi.org/10.1088/1757-899X/878/1/012057. - V.C.S. Rao, A. Manoj, B.R. Swathi. Residual stress measurement of Inconel 600 on different welding techniques by using conventional and XRD methods. Mater. Today: Proc. 41 (2021) 1160–1163. https://doi.org/10.1016/j.matpr.2020.09.403.
- Reza Kashyzadeh, G.H. Farrahi, A. Ahmadi, M. Minaei, M. Ostad Rahimi, S. Barforoushan. Fatigue life analysis in the residual stress field due to resistance spot welding process considering different sheet thicknesses and dissimilar electrode geometries. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications. 237(1) (2023) 33-51. https://doi.org/10.1177/14644207221101069.
- A. Monteiro, S.L.V. Silva, L.V. Silva, A.H.P. Andrade, L.C.E. Silva. Characterization of nickel alloy 600 with ultra-fine structure processed by severe plastic deformation technique (SPD). J. Mater. Sci. Chem. Eng. 5 (2017) 33–44. https://doi.org/10.4236/msce.2017.54004.
- Yi, G.S. Was. Stress and temperature dependence of creep in alloy 600 in primary water. Metall. Mater. Trans. A 32, (2001) 2553–2560. https://doi.org/10.1007/s11661-001-0045-6ю
- Karthik, S. Swaroop. Laser shock peening enhanced corrosion properties in a nickel based nconel 600 superalloy. J. Alloys Compd. 694 (2017) 1309–1319. https://doi.org/10.1016/j.jallcom.2016.10.093.
- Makuch, M. Kulka. Microstructural characterization and some mechanical properties of gas-borided Inconel 600-alloy. Appl. Surf. Sci., 314 (2014) 1007–1018. https://doi.org/10.1016/j.apsusc.2014.06.109.
- ASTM E8-04: Standard Test Methods for Tension Testing of Metallic Materials, ASTM, https://doi.org/10.1520/E0008-04.
- ASTM E466-21: Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials, ASTM, https://doi.org/10.1520/E0466-21.
- P. Skelton. H.J. Maier, H.J. Christ. The Bauschinger effect, Masing model and the Ramberg– Osgood relation for cyclic deformation in metals. Mater. Sci. Eng. A, 238 (1997) 377–390.
https://doi.org/10.1016/S0921-5093(97)00465-6. - Niesłony, C. Dsoki, H. Kaufmann, P. Krug. New method for evaluation of the Manson–Coffin–Basquin and Ramberg– Osgood equations with respect to compatibility. Int. J. Fatigue 30 (2008) 1967–1977. https://doi.org/10.1016/j.ijfatigue.2008.01.012.
- Weixing, X. Kaiquan, G. Yi. On the fatigue notch factor, Kf. Int. J. Fatigue 17(4) (1995) 245–251. https://doi.org/10.1016/0142-1123(95)93538-D.
- E. Dowling. Mechanical behavior of materials, engineering methods for deformation, fracture, and fatigue. fourth ed., Pearson, 2013.
- Zhang. C. Zhang, S. Mu, S. Wang, H. Li. Characterization of mechanical properties of in-service nickel-based alloy by continuous indentation. Structures 48 (2023) 1346–1355. https://doi.org/10.1016/j.istruc.2023.01.053.
References
[1] M.A. Alam, H.H. Ya, S.M. Sapuan, O. Mamat, B. Parveez, M. Yusuf, F. Masood, R.A. Ilyas, Recent advancements in advanced composites for aerospace applications: a review, Adv. Compos. Aerosp. Eng. Appl. (2022) 319–339. https://doi.org/10.1007/978-3-030-88192-4_16.
[2] A.T. Kermanidis, Aircraft aluminum alloys: applications and future trends, Revolutionizing Aircr. Mater. Process. (2020) 21–55. https://doi.org/10.1007/978-3-030-35346-9_2.
[3] M.T. Ali, Z. Jebri, J. Jumel, An enhanced surface treatment for effective bonding of 7075-T6 aluminium alloys, J. Adhes. (2024) 1–17. https://doi.org/10.1080/00218464.2024.2321263.
[4] A.V. Rex, S.K. Paul, A. Singh, Influence of uniaxial and equi-biaxial tensile pre-straining on the high cycle and notch fatigue behaviour of AA2024-T4 aluminium alloy, Theor. Appl. Fract. Mech. 128 (2023) 104176. https://doi.org/10.1016/j.tafmec.2023.104176.
[5] J.T. Burns, J.J. Jones, A.D. Thompson, J.S.W. Locke, Fatigue crack propagation of aerospace aluminum alloy 7075-T651 in high altitude environments, Int. J. Fatigue. 106 (2018) 196–207. https://doi.org/10.1016/j.ijfatigue.2017.09.017.
[6] M.M. Kadhim, S.K. Naif, D.F. Mohammed, A.W. Hussein, The concentration influence of multi-walled carbon nanotubes coating on fatigue edge crack growth and other mechanical properties of Al 7075-T6 thin plates, Results Eng. (2024) 102719. https://doi.org/10.1016/j.rineng.2024.102719 ·.
[7] M.Y. Khalid, R. Umer, K.A. Khan, Review of recent trends and developments in aluminium 7075 alloy and its metal matrix composites (MMCs) for aircraft applications, Results Eng 20 (2023), 101372, (n.d.). https://doi.org/10.1016/j.rineng.2023.101372.
[8] R.M. Nejad, F. Berto, M. Tohidi, Fatigue performance prediction of Al-alloy 2024 plates in riveted joint structure, Eng. Fail. Anal. 126 (2021) 105439. https://doi.org/10.1016/j.engfailanal.2021.105439.
[9] X. Zhang, Y. Chen, J. Hu, Recent advances in the development of aerospace materials, Prog. Aerosp. Sci. 97 (2018) 22–34. https://doi.org/10.1016/j.paerosci.2018.01.001.
[10] H. Zhu, J. Li, Advancements in corrosion protection for aerospace aluminum alloys through surface treatment, Int. J. Electrochem. Sci. (2024) 100487. https://doi.org/10.1016/j.ijoes.2024.100487.
[11] M.G.G. Camarinha, L.C. Campanelli, M.J.R. Barboza, L. Reis, A.A. Couto, D.A.P. Reis, Fatigue behavior of notched and unnotched 7075-T6 aluminum alloy subjected to retrogression and re-aging (RRA) heat treatment and plasma nitriding, Theor. Appl. Fract. Mech. 127 (2023) 104051. https://doi.org/10.1016/j.tafmec.2023.104051.
[12] B.N. Sharath, D.G. Pradeep, K.S. Madhu, A Review on the Potential Impact of Age Hardening on Aluminium Alloys and Hybrid Composites for Engineering Applications, Prog. Eng. Sci. (2024) 100013. https://doi.org/10.1016/j.pes.2024.100013.
[13] A. Moradi, S. Ghorbani, M. Chizari, Experimental research on mechanical, material, and metallurgical properties of Inconel 600: Application in elevated temperature environment, J. Des. Against Fatigue. 2 (2024). https://doi.org/10.62676/jdaf.2024.2.1.30.
[14] J. Brnic, S. Krscanski, M. Brcic, L. Geng, J. Niu, B. Ding, Reliable experimental data as a key factor for design of mechanical structures, Struct. Eng. Mech. An Int’l J. 72 (2019) 245–256. https://doi.org/10.12989/sem.2019.72.2.245.
[15] D. Skejić, T. Dokšanović, I. Čudina, F.M. Mazzolani, The basis for reliability-based mechanical properties of structural aluminium alloys, Appl. Sci. 11 (2021) 4485. https://doi.org/10.3390/app11104485.
[16] M. Benedetti, C. Menapace, V. Fontanari, C. Santus, On the variability in static and cyclic mechanical properties of extruded 7075‐T6 aluminum alloy, Fatigue Fract. Eng. Mater. Struct. 44 (2021) 2975–2989. https://doi.org/DOI: 10.1111/ffe.13530.
[17] X. Zhang, M. Yang, C. Zhou, N. Fu, W. Huang, Z. Wang, A review of in-plane biaxial fatigue behavior of metallic materials, Theor. Appl. Fract. Mech. 123 (2023) 103726. https://doi.org/10.1016/j.tafmec.2022.103726.
[18] J.C. Pang, S.X. Li, Z.G. Wang, Z.F. Zhang, General relation between tensile strength and fatigue strength of metallic materials, Mater. Sci. Eng. A. 564 (2013) 331–341. https://doi.org/10.1016/j.msea.2012.11.103.
[19] C. Gao, M.Q. Yang, J.C. Pang, S.X. Li, M.D. Zou, X.W. Li, Z.F. Zhang, Abnormal relation between tensile and fatigue strengths for a high-strength low-alloy steel, Mater. Sci. Eng. A. 832 (2022) 142418. https://doi.org/10.1016/j.msea.2021.142418.
[20] H. Mughrabi, Cyclic slip irreversibilities and the evolution of fatigue damage, Metall. Mater. Trans. B. 40 (2009) 431–453. https://doi.org/10.1007/s11663-009-9240-4.
[21] R. Liu, Y. Tian, Z. Zhang, X. An, P. Zhang, Z. Zhang, Exceptional high fatigue strength in Cu-15at.% Al alloy with moderate grain size, Sci. Rep. 6 (2016) 27433. https://doi.org/10.1038/srep27433.
[22] A.H. Siddiqui, P. Tiwari, J.P. Patil, A. Tewari, S. Mishra, Yield Locus and Texture Evolution of AA7475-T761 Aluminum Alloy under Planar Biaxial Loading: An Experimental and Analytical Study, J. Alloys Compd. (2024) 175115. https://doi.org/10.1016/j.jallcom.2024.175115.
[23] S. Hashemian, P.M. Keshtiban, A.E. haghi Oskui, Fracture behavior of the forged aluminum 7075-T6 alloy under mixed-mode loading conditions, Eng. Fail. Anal. 140 (2022) 106610. https://doi.org/10.1016/j.engfailanal.2022.106610.
[24] V. Chaves, G. Beretta, J.A. Balbín, A. Navarro, Fatigue life and crack growth direction in 7075-T6 aluminium alloy specimens with a circular hole under biaxial loading, Int. J. Fatigue. 125 (2019) 222–236. https://doi.org/10.1016/j.ijfatigue.2019.03.031.
[25] R. Nwawe, M. Grasso, Y. Chen, J. Klusak, & V. Rosiello, Optimisation of a gigacycle biaxial fatigue specimen for ultrasonic testing. Proceedings of Abstracts Engineering and Computer Science Research Conference 2019 (pp. 8–10). Hatfield, UK: University of Hertfordshire, (2019), DOI: 10.18745/pb.21692.
[26] P. Costa, R. Nwawe, H. Soares, L. Reis, M. Freitas, Y. Chen, D. Montalvão, Review of Multiaxial Testing for Very High Cycle Fatigue: From ‘Conventional’ to Ultrasonic Machines. Machines 2020, 8, 25. (2020) https://doi.org/10.3390/machines8020025.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Arash Moradi , Siamak Ghorbani, Mahmoud Chizari (Author)

This work is licensed under a Creative Commons Attribution 4.0 International License.