Rotating Bending Fatigue Durability of ferritic nitrocarburized Wrought 304 Stainless Steel: A Comparative Study of Surface-Treated vs. Untreated Specimen
DOI:
https://doi.org/10.62676/jdaf.2024.2.2.10Keywords:
Rotating bending fatigue; stainless steel 304; surface treatment; machine learning., Rotating bending fatigue, Surface treatment, Stainless steel 304, machine learningAbstract
The rotating bending fatigue test, which is a common durability test for industrial components, was employed in this study to examine the impact of the surface treatment procedure on the material's performance under room temperature. The studied material in this research is a wrought stainless steel (SS) 304 alloy that has undergone a specialized surface treatment to enhance the fatigue properties of this unique material. The fatigue endurance of untreated materials was 405 MPa (65% of untreated specimen’s yield strength) on 5 million runout cycles, while the surface-treated samples exhibited 545 MPa (85% of treated specimen’s yield strength), a significantly greater value compared to the untreated ones (even up to 10 million runout cycles). The experimental results demonstrated that the surface-treated samples exhibited no signs of cracking. Instead, all failures were attributed to plastic bending, particularly at higher stress levels. Furthermore, the samples displayed a limited range of stress levels, spanning from endurance to plastic bending conditions. This finding suggests that the hypothesis of an increase in stiffness in the surface layer is more pronounced than in the material interior. It also indicates that the surface layer material was not cracked under the maximum stress level, while the layer beneath it experienced plastic deformation. A comparison has been made between the Basquin equation and a statistical machine learning model (for a limited amount of data) to incorporate the impact of surface treatment on predicting fatigue lifetime, and the random forest regressor model would be able to predict the lifetime with the accuracy of R2= 87% which was much higher than the classical model.
References
[1] R.R. Kumar, R.K. Gupta, A. Sarkar, M. Prasad, Vacuum diffusion bonding of α‑titanium alloy to stainless steel for aerospace applications: Interfacial microstructure and mechanical characteristics, Materials Characterization 183 (2022) 111607.
https://doi.org/10.1016/j.matchar.2021.111607
[2] K.K. Pradhan, C.R. Matawale, Heat treatment analysis of SS304 for gas turbine application, Materials Today: Proceedings 33 (2020) 5734-5739.
https://doi.org/10.1016/j.matpr.2020.05.102
[3] A. Arifin, I. Yani, Failure analysis of AISI 304 stainless steel pipeline transmission a petrochemical plant, IOP Publishing, p. 012006.
https://doi.org/10.1088/1757-899X/857/1/012006
[4] H.M. Raheem, I. Altayer, H.S. Mohamed, M.H. Al-maamori, Metallurgical Failure Analysis: A Case Study of Observing a Leak in a Stainless Steel SS304 Pipe, Petroleum Chemistry 64(1) (2024) 134-143.
https://doi.org/10.1134/S096554412402004X
[5] A. Behvar, Y. Aghayar, M. Avateffazeli, A. Tridello, A. Benelli, D.S. Paolino, M. Mohammadi, M. Haghshenas, Synergistic impact of corrosion pitting on the rotating bending fatigue of additively manufactured 316L stainless steel: Integrated experimental and modeling analyses, International Journal of Fatigue 188 (2024) 108491.
https://doi.org/10.1016/j.ijfatigue.2024.108491
[6] A. Behvar, F. Berto, M. Haghshenas, A review on isothermal rotating bending fatigue failure: Microstructural and lifetime modeling of wrought and additive manufactured alloys, Fatigue & Fracture of Engineering Materials & Structures 46(10) (2023) 3545-3595.
https://doi.org/10.1111/ffe.14094
[7] K.S. Chan, Roles of microstructure in fatigue crack initiation, International Journal of Fatigue 32(9) (2010) 1428-1447.
https://doi.org/10.1016/j.ijfatigue.2009.10.005
[8] T. Mura, A theory of fatigue crack initiation, Materials Science and Engineering: A 176(1-2) (1994) 61-70.
https://doi.org/10.1016/0921-5093(94)90959-8
[9] R.I. Stephens, A. Fatemi, R.R. Stephens, H.O. Fuchs, Metal fatigue in engineering, John Wiley & Sons2000.
Link: Book
[10] S. Yang, W. Zeng, J. Yang, Characterization of shot peening properties and modelling on the fatigue performance of 304 austenitic stainless steel, International Journal of Fatigue 137 (2020) 105621.
https://doi.org/10.1016/j.ijfatigue.2020.105621
[11] S. Yang, Investigations on the changed intensity shot peening specimens machined from SS304: process characterization, fatigue modeling, and failure analyses, The International Journal of Advanced Manufacturing Technology 120(7) (2022) 5041-5056.
https://doi.org/10.1007/s00170-022-09063-w
[12] B.B. Fernandes, S. Mändl, R.M. Oliveira, M. Ueda, Mechanical properties of nitrogen-rich surface layers on SS304 treated by plasma immersion ion implantation, Applied Surface Science 310 (2014) 278-283.
https://doi.org/10.1016/j.apsusc.2014.04.142
[13] C. Ye, C. Zhang, J. Zhao, Y. Dong, Effects of post-processing on the surface finish, porosity, residual stresses, and fatigue performance of additive manufactured metals: a review, Journal of Materials Engineering and Performance 30 (2021) 6407-6425.
https://doi.org/10.1007/s11665-021-06021-7
[14] L. Shen, L. Wang, Y. Wang, C. Wang, Plasma nitriding of AISI 304 austenitic stainless steel with pre-shot peening, Surface and Coatings Technology 204(20) (2010) 3222-3227.
https://doi.org/10.1016/j.surfcoat.2010.03.018
[15] Y.-H. Chung, T.-C. Chen, H.-B. Lee, L.-W. Tsay, Effect of micro-shot peening on the fatigue performance of AISI 304 stainless steel, Metals 11(9) (2021) 1408.
https://doi.org/10.3390/met11091408
[16] K. Praveenkumar, S. Swaroop, G. Manivasagam, Effect of multiple laser peening on microstructural, fatigue and fretting-wear behaviour of austenitic stainless steel, Surface and coatings technology 443 (2022) 128611.
https://doi.org/10.1016/j.surfcoat.2022.128611
[17] J. Colin, A. Fatemi, S. Taheri, Fatigue behavior of stainless steel 304L including strain hardening, prestraining, and mean stress effects, (2010).
https://doi.org/10.1115/1.4000224
[18] Z. Liu, S. Wang, Y. Feng, X. Wang, Y. Peng, J. Gong, Exploration on the fatigue behavior of low-temperature carburized 316L austenitic stainless steel at elevated temperature, Materials Science and Engineering: A 850 (2022) 143562.
https://doi.org/10.1016/j.msea.2022.143562
[19] S. Aguado-Montero, J. Vázquez, C. Navarro, J. Domínguez, Optimal shot peening residual stress profile for fatigue, Theoretical and Applied Fracture Mechanics 116 (2021) 103109.
https://doi.org/10.1016/j.tafmec.2021.103109
[20] T. Wiriyasaroj, P. Juijerm, B. Scholtes, T. Niendorf, Fatigue and cyclic deformation behavior of non-and boronized austenitic stainless steel AISI 304 at room and elevated temperatures, Songklanakarin Journal of Science & Technology 41(2) (2019).
https://www.thaiscience.info/Journals/Article/SONG/10993250.pdf
[21] D. Kumar, S. Idapalapati, W. Wang, S. Narasimalu, Effect of surface mechanical treatments on the microstructure-property-performance of engineering alloys, Materials 12(16) (2019) 2503.
https://doi.org/10.3390/ma12162503
[22] I. Altenberger, B. Scholtes, Improvement of fatigue behaviour of mechanically surface treated materials by annealing, Scripta materialia 41(8) (1999) 873-881.
https://doi.org/10.1016/S1359-6462(99)00222-5
[23] S. Suresh, Graded materials for resistance to contact deformation and damage, Science 292(5526) (2001) 2447-2451.
https://doi.org/10.1126/science.1059716
[24] S.M. Banavasi, K.S. Ravishankar, S.N. Padmayya, A Review on Design and Fabrication of Fatigue Testing Machine, International Journal of Novel Research and Development 3(5) (2018) 5-14.
ISSN: 2456-4184
[25] J.M.E. Marques, D. Benasciutti, A. Niesłony, J. Slavič, An overview of fatigue testing systems for metals under uniaxial and multiaxial random loadings, Metals 11(3) (2021) 447.
https://doi.org/10.3390/met11030447
[26] Z. Liu, S. Wang, Y. Feng, Y. Peng, J. Gong, M.A.J. Somers, Residual stress relaxation in the carburized case of austenitic stainless steel under alternating loading, International Journal of Fatigue 159 (2022) 106837.
https://doi.org/10.1016/j.ijfatigue.2022.106837
[27] A. Tajiri, T. Nozaki, Y. Uematsu, T. Kakiuchi, M. Nakajima, Y. Nakamura, H. Tanaka, Fatigue limit prediction of large scale cast aluminum alloy A356, Procedia materials science 3 (2014) 924-929.
https://doi.org/10.1016/j.mspro.2014.06.150
[28] C.A. Molina, M.D. Chapetti, Estimation of high cycle fatigue behaviour using a threshold curve concept, International Journal of Fatigue 108 (2018) 47-52.
https://doi.org/10.1016/j.ijfatigue.2017.11.007
[29] W.W. Gerberich, S.E. Harvey, D.E. Kramer, J.W. Hoehn, Low and high cycle fatigue—A continuum supported by AFM observations, Acta materialia 46(14) (1998) 5007-5021.
https://doi.org/10.1016/S1359-6454(98)00169-4
[30] Y.-S. Shih, J.-J. Chen, The frequency effect on the fatigue crack growth rate of 304 stainless steel, Nuclear engineering and design 191(2) (1999) 225-230.
https://doi.org/10.1016/S0029-5493(99)00144-2
[31] A. Behvar, Y. Aghayar, M. Avateffazeli, A. Tridello, A. Benelli, D.S. Paolino, M. Mohammadi, M. Haghshenas, Synergistic impact of corrosion pitting on the rotating bending fatigue of additively manufactured 316L stainless steel: Integrated experimental and modeling analyses, International Journal of Fatigue (2024) 108491.
https://doi.org/10.1016/j.ijfatigue.2024.108491
[32] E. Macherauch, Introduction to residual stress, Advances in surface treatments 4 (2014) 1-36.
Link: Book
[33] H. Arora, R. Singh, G.S. Brar, Numerical simulation on residual stresses of stainless steel SS-304 thin welded pipe, Measurement and Control 53(7-8) (2020) 1183-1193.
https://doi.org/10.1177/0020294020917173
[34] D.J. Bacon, Y.N. Osetsky, D. Rodney, Dislocation–obstacle interactions at the atomic level, Dislocations in solids 15 (2009) 1-90.
https://doi.org/10.1016/S1572-4859(09)01501-0
[35] I. Baker, Interstitial strengthening in fcc metals and alloys, Advanced Powder Materials 1(4) (2022) 100034.
https://doi.org/10.1016/j.apmate.2022.100034
[36] B. Clausen, M. Steinbacher, F. Hoffmann, Residual Stresses and Distortion in Thermochemically Treated Steels, Steel Heat Treating Technologies, ASM International2014, pp. 375-390.
https://doi.org/10.31399/asm.hb.v04b.a0005956
[37] S. Jegou, L. Barrallier, R. Kubler, Residual stress development during nitriding of steels, Trans Tech Publ, pp. 370-373.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Alireza Behvar, Onome Scott-Emuakpor , Kevin James , Bradley Crannell, Meysam Haghshenas (Author)

This work is licensed under a Creative Commons Attribution 4.0 International License.