Failure strength of 7075-T6 aluminium alloy: integrating digital image and finite element analysis for static uniaxial and biaxial load scenariosl and Biaxial Load Scenarios

Authors

  • Fatemeh Marashi Researcher of sahand university of technology Author
  • Mahmoud Chizari Author
  • Ogunjobi Kehinde Emmanuel Author
  • Richard Nwawe Tchadeu Author
  • Hossein Madani Author

DOI:

https://doi.org/10.62676/jdaf.2024.2.2.20

Keywords:

7075-T6 Aluminium alloy; uniaxial and biaxial loads; digital image correlation; numerical and experimental simulations, Aluminum 7075-T6, Fatigue strength, Digital image correlation, uniaxial loading, biaxial loading, Numerical simulation, Experimental simulation

Abstract

The objective of this study is to investigate the mechanical properties of 7075-T6 Aluminium (Al) alloy under both uniaxial and biaxial loads. The study will be conducted using a combination of experimental and numerical methods. The experimental method used is the digital image correlation (DIC) technique, which was utilized to capture the deformation and strain fields of the material specimen under tensile test. A tensile machine was employed to apply uniaxial and biaxial loads on the sample. The strain and deformation distribution of the results was generated on the DIC and correlated software. The numerical method involved the use of a commercial finite element software to create a finite element model and simulate the mechanical behaviour of the material under the same loading conditions. The results obtained from the experimental and numerical methods were compared to validate the accuracy of the numerical model. The outcomes demonstrated that under uniaxial loading, localized necking and fracture were observed, while biaxial loading resulted in shear deformation and fracture. This research contributes to the development of more accurate models for predicting the mechanical behaviour of the model samples under different loading conditions.

References

[1] M.A. Alam, H.H. Ya, S.M. Sapuan, O. Mamat, B. Parveez, M. Yusuf, F. Masood, R.A. Ilyas, Recent advancements in advanced composites for aerospace applications: a review, Adv. Compos. Aerosp. Eng. Appl. (2022) 319–339. https://doi.org/10.1007/978-3-030-88192-4_16.

[2] A.T. Kermanidis, Aircraft aluminum alloys: applications and future trends, Revolutionizing Aircr. Mater. Process. (2020) 21–55. https://doi.org/10.1007/978-3-030-35346-9_2.

[3] M.T. Ali, Z. Jebri, J. Jumel, An enhanced surface treatment for effective bonding of 7075-T6 aluminium alloys, J. Adhes. (2024) 1–17. https://doi.org/10.1080/00218464.2024.2321263.

[4] A.V. Rex, S.K. Paul, A. Singh, Influence of uniaxial and equi-biaxial tensile pre-straining on the high cycle and notch fatigue behaviour of AA2024-T4 aluminium alloy, Theor. Appl. Fract. Mech. 128 (2023) 104176. https://doi.org/10.1016/j.tafmec.2023.104176.

[5] J.T. Burns, J.J. Jones, A.D. Thompson, J.S.W. Locke, Fatigue crack propagation of aerospace aluminum alloy 7075-T651 in high altitude environments, Int. J. Fatigue. 106 (2018) 196–207. https://doi.org/10.1016/j.ijfatigue.2017.09.017.

[6] M.M. Kadhim, S.K. Naif, D.F. Mohammed, A.W. Hussein, The concentration influence of multi-walled carbon nanotubes coating on fatigue edge crack growth and other mechanical properties of Al 7075-T6 thin plates, Results Eng. (2024) 102719. https://doi.org/10.1016/j.rineng.2024.102719 ·.

[7] M.Y. Khalid, R. Umer, K.A. Khan, Review of recent trends and developments in aluminium 7075 alloy and its metal matrix composites (MMCs) for aircraft applications, Results Eng 20 (2023), 101372, (n.d.). https://doi.org/10.1016/j.rineng.2023.101372.

[8] R.M. Nejad, F. Berto, M. Tohidi, Fatigue performance prediction of Al-alloy 2024 plates in riveted joint structure, Eng. Fail. Anal. 126 (2021) 105439. https://doi.org/10.1016/j.engfailanal.2021.105439.

[9] X. Zhang, Y. Chen, J. Hu, Recent advances in the development of aerospace materials, Prog. Aerosp. Sci. 97 (2018) 22–34. https://doi.org/10.1016/j.paerosci.2018.01.001.

[10] H. Zhu, J. Li, Advancements in corrosion protection for aerospace aluminum alloys through surface treatment, Int. J. Electrochem. Sci. (2024) 100487. https://doi.org/10.1016/j.ijoes.2024.100487.

[11] M.G.G. Camarinha, L.C. Campanelli, M.J.R. Barboza, L. Reis, A.A. Couto, D.A.P. Reis, Fatigue behavior of notched and unnotched 7075-T6 aluminum alloy subjected to retrogression and re-aging (RRA) heat treatment and plasma nitriding, Theor. Appl. Fract. Mech. 127 (2023) 104051. https://doi.org/10.1016/j.tafmec.2023.104051.

[12] B.N. Sharath, D.G. Pradeep, K.S. Madhu, A Review on the Potential Impact of Age Hardening on Aluminium Alloys and Hybrid Composites for Engineering Applications, Prog. Eng. Sci. (2024) 100013. https://doi.org/10.1016/j.pes.2024.100013.

[13] A. Moradi, S. Ghorbani, M. Chizari, Experimental research on mechanical, material, and metallurgical properties of Inconel 600: Application in elevated temperature environment, J. Des. Against Fatigue. 2 (2024). https://doi.org/10.62676/jdaf.2024.2.1.30.

[14] J. Brnic, S. Krscanski, M. Brcic, L. Geng, J. Niu, B. Ding, Reliable experimental data as a key factor for design of mechanical structures, Struct. Eng. Mech. An Int’l J. 72 (2019) 245–256. https://doi.org/10.12989/sem.2019.72.2.245.

[15] D. Skejić, T. Dokšanović, I. Čudina, F.M. Mazzolani, The basis for reliability-based mechanical properties of structural aluminium alloys, Appl. Sci. 11 (2021) 4485. https://doi.org/10.3390/app11104485.

[16] M. Benedetti, C. Menapace, V. Fontanari, C. Santus, On the variability in static and cyclic mechanical properties of extruded 7075‐T6 aluminum alloy, Fatigue Fract. Eng. Mater. Struct. 44 (2021) 2975–2989. https://doi.org/DOI: 10.1111/ffe.13530.

[17] X. Zhang, M. Yang, C. Zhou, N. Fu, W. Huang, Z. Wang, A review of in-plane biaxial fatigue behavior of metallic materials, Theor. Appl. Fract. Mech. 123 (2023) 103726. https://doi.org/10.1016/j.tafmec.2022.103726.

[18] J.C. Pang, S.X. Li, Z.G. Wang, Z.F. Zhang, General relation between tensile strength and fatigue strength of metallic materials, Mater. Sci. Eng. A. 564 (2013) 331–341. https://doi.org/10.1016/j.msea.2012.11.103.

[19] C. Gao, M.Q. Yang, J.C. Pang, S.X. Li, M.D. Zou, X.W. Li, Z.F. Zhang, Abnormal relation between tensile and fatigue strengths for a high-strength low-alloy steel, Mater. Sci. Eng. A. 832 (2022) 142418. https://doi.org/10.1016/j.msea.2021.142418.

[20] H. Mughrabi, Cyclic slip irreversibilities and the evolution of fatigue damage, Metall. Mater. Trans. B. 40 (2009) 431–453. https://doi.org/10.1007/s11663-009-9240-4.

[21] R. Liu, Y. Tian, Z. Zhang, X. An, P. Zhang, Z. Zhang, Exceptional high fatigue strength in Cu-15at.% Al alloy with moderate grain size, Sci. Rep. 6 (2016) 27433. https://doi.org/10.1038/srep27433.

[22] A.H. Siddiqui, P. Tiwari, J.P. Patil, A. Tewari, S. Mishra, Yield Locus and Texture Evolution of AA7475-T761 Aluminum Alloy under Planar Biaxial Loading: An Experimental and Analytical Study, J. Alloys Compd. (2024) 175115. https://doi.org/10.1016/j.jallcom.2024.175115.

[23] S. Hashemian, P.M. Keshtiban, A.E. haghi Oskui, Fracture behavior of the forged aluminum 7075-T6 alloy under mixed-mode loading conditions, Eng. Fail. Anal. 140 (2022) 106610. https://doi.org/10.1016/j.engfailanal.2022.106610.

[24] V. Chaves, G. Beretta, J.A. Balbín, A. Navarro, Fatigue life and crack growth direction in 7075-T6 aluminium alloy specimens with a circular hole under biaxial loading, Int. J. Fatigue. 125 (2019) 222–236. https://doi.org/10.1016/j.ijfatigue.2019.03.031.

[25] R. Nwawe, M. Grasso, Y. Chen, J. Klusak, & V. Rosiello, Optimisation of a gigacycle biaxial fatigue specimen for ultrasonic testing. Proceedings of Abstracts Engineering and Computer Science Research Conference 2019 (pp. 8–10). Hatfield, UK: University of Hertfordshire, (2019), DOI: 10.18745/pb.21692.

[26] P. Costa, R. Nwawe, H. Soares, L. Reis, M. Freitas, Y. Chen, D. Montalvão, Review of Multiaxial Testing for Very High Cycle Fatigue: From ‘Conventional’ to Ultrasonic Machines. Machines 2020, 8, 25. (2020) https://doi.org/10.3390/machines8020025.

Downloads

Published

2024-11-06

How to Cite

Marashi, F., Chizari, M., Emmanuel, O. K., Tchadeu, R. N., & Madani, H. (2024). Failure strength of 7075-T6 aluminium alloy: integrating digital image and finite element analysis for static uniaxial and biaxial load scenariosl and Biaxial Load Scenarios. Journal of Design Against Fatigue, 2(2), 13-21. https://doi.org/10.62676/jdaf.2024.2.2.20