Fracture Analysis of Copper Cathode and Function Optimization of the Cathode Stripping Machine (CSM)
DOI:
https://doi.org/10.62676/jdaf.2025.3.1.30Keywords:
Fracture, Cathode blank, CZM, CZM, FEM, Fracture analysis, Cathode Stripping Machine (CSM)Abstract
Incorrect separation of copper cathode from the stainless-steel cathode blank in the cathode separation machine (CSM) is a significant factor affecting the production efficiency. This study investigates the conditions leading to improper cathode separation and explores ways to address this issue. Experimental observations show that the thickness of the cathode, the formation of nodules on the cathode, and the positioning of the flex mechanism in the (CSM) significantly influence the separation of cathodes from the cathode blanks. Once, twenty-four cathodes were randomly selected from the CSM output at Sarcheshmeh Copper Refinery (Rafsanjan, Iran). The thickness, opening, and length of the opening formed in the cathodes separated from the cathode blanks were measured. Subsequently, after model validation and simulation strategies, the cathode separation process, involving the application of impact by the flex, was simulated using the finite element method (FEM) with the cohesive zone model (CZM). In the FEM simulation, CZM was applied under the assumption of plane strain and considering fracture energy to predict the changes in the separation layers of the cathode from the cathode blank. Simulation results indicate that shifting the position of the flex increases the crack width and length of the cathode from the cathode blank. Finally, based on the simulation results, a mechanism to optimize the impact location for more efficient cathode separation was designed and improved the machine for CSM in practical.
References
[1] M. E. Schlesinger, K. C. Sole and W. G. Davenport, Extractive metallurgy of copper .Elsevier, 2011. https://doi.org/10.1016/C2010-0-64841-3
[2] N. Aslin, O. Eriksson, G. Heferen, and G. S. Yek, "Developments in Cathode Stripping Machines - An Integrated Approach for Improved Efficiency," Proceedings of Cu, p. 1, 2010.
[3] M. Shojaei, G. R. Khayati, S. M. J. Khorasani, and R. K. Hernashki, "Investigation of spring back phenomenon in the 316L stainless steel cathode blank based on the changes in electrical resistivity and magnetic properties due to the residual stress and martensite phase formation: an industrial failure," Engineering Failure Analysis, vol. 126, p. 105473, 2021.https://doi.org/10.1016/j.engfailanal.2021.105473
[4] K. Wu et al., "Interfacial strength-controlled energy dissipation mechanism and optimization in impact-resistant nacreous structure," Materials & Design, vol. 163, p. 107532, 2019. https://doi.org/10.1016/j.matdes.2018.107532
[5] W. Armstrong and C. Refineries, "The ISA PROCESS and its contribution to electrolytic copper," Rautomead Conference, Scotland, 1999.
[6] F. Volpi et al., "A capacitance-based solution to monitor absolute crack length in four-point bending test: Modelling and experiments," Sensors and Actuators A: Physical, vol. 254, pp. 145-151, 2017. https://doi.org/10.1016/j.sna.2016.12.017
[7] D. Höwer, B. A. Lerch, B. A. Bednarcyk, E. J. Pineda, S. Reese, and J.-W. Simon, "Cohesive zone modeling for mode I facesheet to core delamination of sandwich panels accounting for fiber bridging," Composite Structures, vol. 183, pp. 568-581, 2018. https://doi.org/10.1016/j.compstruct.2017.07.005
[8] X. Zhang, Z.-y. Cai, J.-x. Gao, and M.-w. Wang, "Numerical analysis of face sheet/core debonding failure in the plastic forming of aluminum foam sandwich panel," The International Journal of Advanced Manufacturing Technology, vol. 128, no. 5-6,pp.2285-2300,2023. https://doi.org/10.1007/s00170-023-12087-5
[9] J. Correia, R Campilho, R. Rocha, Y. Liu, and L. Ramalho, "Parametric study of composite curved adhesive joints," The International Journal of Advanced Manufacturing Technology, vol. 111, pp. 2957-2970, 2020. https://doi.org/10.1007/s00170-020-06314-6
[10] B. Aryal, E. Morozov, H. Wang, K. Shankar, P. Hazell, and J. Escobedo-Diaz, "Effects of impact energy, velocity, and impactor mass on the damage induced in composite laminates and sandwich panels," Composite Structures, vol. 226, p. 111284, 2019. https://doi.org/10.1016/j.compstruct.2019.111284
[11] N. Almeida, V. Ciminelli, P. Cetlin, and D. Majuste, "Cathode stripping behavior: Simulation by the finite element method and experimental effect of cathode surface roughness and its repeated use," Hydrometallurgy, vol. 220, p. 106103, 2023. https://doi.org/10.1016/j.hydromet.2023.106103
[12] W. Chen, F.-l. Huang, Z.-h. Zeng, Z.-j. Wang, and A.-g. Pi, "Microstructure and mechanical properties of heterogeneous-gradient composite plates with a sphere-array interlayer prepared using explosive welding," Journal of Materials Research and Technology, vol. 30, pp. 6508-6519, 2024. https://doi.org/10.1016/j.jmrt.2024.05.054
[13] M. Boomeri, K. Nakashima, and D. R. Lentz, "The Sarcheshmeh porphyry copper deposit, Kerman, Iran: A mineralogical analysis of the igneous rocks and alteration zones including halogen element systematics related to Cu mineralization processes," Ore Geology Reviews, vol. 38, no. 4, pp. 367-381, 2010.https://doi.org/10.1016/j.oregeorev.2010.09.001
[14] S. Shakibania, M. Mokmeli, and S. M. J. Khorasani, "Statistical analysis of factors affecting the anode scrap rate at the Khatoon Abad Copper Refinery Plant," Metallurgical and Materials Transactions B, pp. 1-16, 2022. https://doi.org/10.1007/s11663-021-02373-6
[15] A. Morales-Aragon, D. Sánchez-Rodas, G. Ríos, and M. S. Moats, "Impurity Behavior in Cast Copper Anodes: Implications for Electrorefining in a Circular Economy," Metals, vol. 15, no. 2, p. 113, 2025. https://doi.org/10.3390/met15020113
[16] M. Chen, X. Xiao, H. Guo, and J. Tong, "Deformation behavior, microstructure and mechanical properties of pure copper subjected to tube hydroforming," Materials Science and Engineering: A,vol.731,pp.331-343,2018. https://doi.org/10.1016/j.msea.2018.06.068
[17] J. Horak, V. Sikka, and D. Raske, "Review of mechanical properties and microstructures of Types 304 and 316 stainless steel after long-term aging," Oak Ridge National Lab., TN (USA); Argonne National Lab.,IL(USA),1983. https://www.osti.gov/biblio/588934
[18] K. Park and G. H. Paulino, "Cohesive zone models: a critical review of traction-separation relationships across fracture surfaces," Applied Mechanics Reviews, vol. 64, no. 6, p. 060802, 2011. https://doi.org/10.1115/1.4023110
[19] C. Sarrado, F. A. Leone, and A. Turon, "Finite-thickness cohesive elements for modeling thick adhesives," Engineering Fracture Mechanics, vol. 168, pp.105-113,2016. https://doi.org/10.1016/j.engfracmech.2016.03.020
[20] P. Papanastasiou and E. Sarris, "Cohesive zone models," in Porous rock fracture mechanics: Elsevier, 2017, pp. 119-144. https://doi.org/10.1016/B978-0-08-100781-5.00006-3
[21] P. Saikia and N. Muthu, "Estimation of CZM Parameters for Investigating the Interface Fracture of Adhesively Bonded Joints Under Mode I, Mode II, and Mixed-Mode (I/II) Loading," Fatigue & Fracture of Engineering Materials & Structures, vol. 47, no. 12, pp.4636-4649,2024. https://doi.org/10.1111/ffe.14457
[22] A. Akhavan-Safar, E. A. Marques, R. J. Carbas, and L. F. da Silva, "Cohesive Zone Modelling - CZM," in Cohesive Zone Modelling for Fatigue Life Analysis of Adhesive Joints: Springer, 2022, pp. 19-42. https://doi.org/10.1007/978-3-030-93142-1
[23] A. Khabazaghdam, B. Behjat, M. Yazdani, L. F. Da Silva, E. Marques, and X. Shang, "Creep behaviour of a graphene-reinforced epoxy adhesively bonded joint: experimental and numerical investigation," The Journal of Adhesion, vol. 97, no. 13, pp. 1189-1210, 2021. https://doi.org/10.1080/00218464.2020.1742114
Downloads
Published
Issue
Section
License
Copyright (c) 2025 Mohammad Reza Dashtbayazi, Mohsen Forouzanmehr, Masoud Raoufi Jahromi, Seyedhamed Pourbagheri (Author)

This work is licensed under a Creative Commons Attribution 4.0 International License.