A study on the effect of plasticity on the measurement of residual stresses using ultrasound technique
DOI:
https://doi.org/10.62676/d8hb0f93Keywords:
Ultrasound method; Residual stresses; Plasticity; Finite element analysis.Abstract
Residual stresses can have detrimental effect on the life cycle of engineering components and can affect the accuracy of the fatigue life prediction models. Accurate measurement of these stresses are therefore crucial. . However, destructive and semi-destructive methods of measuring residual stresses often cause damage to the components. In contrast, the non-destructive ultrasonic method allows for intact measurement of residual stresses even, in situation where portability is not feasible. Various waves can be utilized in the ultrasonic method for measuring residual stresses. In this study, longitudinal critically refracted (LCR) waves were employed due to their higher sensitivity, larger scanning area, and lower sensitivity to texture effect, making them preferable over other waves. The purpose of this study was to investigate the influence of plasticity on the measurement of residual stresses using the ultrasonic method. To achieve this, two stainless steel disks were subjected to quenching at temperatures of 300 °C and 700 °C to induce different levels of residual stresses and plasticity. The material properties of the disks were determined through standard tensile tests to facilitate numerical simulations. Tensile test specimens were extracted from the initial sheet to measure the yield stress and modulus of elasticity. The coefficient of acoustoelasticity, was determined by subjecting the tensile test specimens to different stress levels and recording the wave flight time. The coefficient of acoustoelasticity for stainless steel 316Lwas obtained using the slope of and (E(t-t0))/t0,. Residual stresses were experimentally measured using both the ultrasonic method and the center-hole drilling method, and the results were compared with those obtained from numerical analyses. The findings from center-hole drilling method, ultrasonic method, and numerical simulation were then compared and discussed. Different levels of plasticity were considered, and the accuracy of measuring residual stresses was analyzed and evaluated.
References
1. . F. D. Murnaghan, Finite Deformation of an Elastic Solid, Wiley, New York, 1951.
2. . D. S. Hughes, J. L. Kelly, Second Order Elastic Deformation of Solids, Physical Review 92 (1953) 1145-1149, https://doi.org/10.1103/PhysRev.92.1145
3. . R. M. Bergman, R. A. Shahbender, Effect of Statically Applied Stressrs on the Velocity of Propagation of Ultrasonic Waves, J. Appl. Phys. 29 (1958) 1736–1738, https://doi.org/10.1063/1.1723035
4. . R. W. Benson, V. J. Realson, Acoustoelasticity, Prod. Eng. 30 (1959) 56-59.
5. . T. Leon-Salamanca, D. E. Bray, Residual Stress Measurements in Steel Plates and Welds Using Critically Refracted (LCR) Waves, Research in Nondestructive Evaluation 7 (1995) 169–184, https://doi.org/10.1007/BF01606385
6. . P. Junghans, D. E. Bray, Beam Characteristics of High Angle Longitudinal Wave Probes NDE: Applications, Advanced Method, and codes and Standards, Proceedings ASME Pressure Vessels and Piping Conference, 9 (1991) 23-27
7. . M. Srinivasan, D. E. Bray, P. Junghans, A. Alagarsamy, Critically Refracted Longitudinal Wayes Technique: A New Tool for the Measurement of Residual Stresses in Castings, AFS (American Foundrymen Society) 91 (1991)
8. . D. I. Crecraft, The Measurement of Applied and Residual Stresses In Metals Using Ultrasonic Waves, J. Sound vid. 5 (1967) 173-192, https://doi.org/10.1016/0022-460X(67)90186-1
9. . D. M. Egle, D. E. Bray, Measurement of Acoustoelastic and Third Order Elastic Constants for Rail Steel, J. Acoust. Soc. Am. 60 (1976) 741–744, https://doi.org/10.1121/1.381146.
10. . A. A. D. Santos, D. E. Bray, Comparison of Acoustoelastic Methods to Evaluate Stresses in steel Plates and Bars, Journal of Pressure Vessel Technology 124 (2002), 354-358, https://doi.org/10.1115/1.1484114
11. K. Jhang, H. Quan, J. Ha, N. Kim 2006, Estimation of clamping force in high-tension bolts through ultrasonic velocity measurement, Ultrasonics 44 (2006) 1339-1342. https://doi.org/10.1016/j.ultras.2006.05.190.
12. V. Albuquerque, C. Silva, P. Normando, E. Moura, J. Tavares, Thermal aging effects on the microstructure of Nb-bearing nickel-based superalloy weld overlays using ultrasound techniques, Materials & Design 36 (2012) 337-347. https://doi.org/10.1016/j.matdes.2011.11.035
13. . T. Leon-Salamanca, Ultrasonic Measurement of residual stress in steels using Critically Refracted Longitudinal Waves (Ler), Texas A & M University, Department of Mechanical Engineering (1988).
14. . D. E. Bray, P. G. Junghans, Applications of the LCR Ultrasonic Technique for Evaluation of Post-Weld Heat Treatment in Steel Plates, NDT&E International, 28 (1995) 235-242, https://doi.org/10.1016/0963-8695(95)00020-X.
15. . E. Tanala, G. Bourse, M. Fremiot, J. F. De Belleval, Determination of near surface residual stresses on welded joints using ultrasonic methods, NDT&E International 28 (1995) 83-88, https://doi.org/10.1016/0963-8695(94)00013-A.
16. . W. Tang, D. E. Bray, Stress and Yielding Studies Using Critically Refracted Longitudinal Waves, American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP, 322 (1996) 41-48.
17. . T. Leon-Salamanca, D. E. Bray, Residual Stress Measurements in Steel Plates and Welds Using Critically Refracted (LCR) Waves. Research in Nondestructive Evaluation, 7 (1996) 169–184, https://doi.org/10.1007/BF01606385
18. . D. E. Bray, W. Tang, D. Grewal, Ultrasonic Stress Evaluation in a Turbine/Compressor Rotor. Journal of Testing and Evaluation, 25 (1997), https://doi.org/10.1520/JTE11361J.
19. . D. E. Bray, S-J. KIM, M. Fernandes, Ultrasonic Evaluation of Residual Stresses in Rolled Aluminum Plates, American Institute of Physics 497 (1999), 443- 448, https://doi.org/10.1063/1.1303086
20. . R. Acevedo, P. Sedlak, R. Kolman, M. Fredel, Residual stress analysis of additive manufacturing of metallic parts using ultrasonic waves: State of the art review, Journal of Materials Research and Technology 9 (2020) 9457-9477, https://doi.org/10.1016/j.jmrt.2020.05.092
21. . Y. Zhan, Y. Li, E. Zhang, Y. GE, C. Liu, Laser ultrasonic technology for residual stress measurement of 7075 aluminum alloy friction stir welding, Applied Acoustics 145 (2019) 52-59, https://doi.org/10.1016/j.apacoust.2018.09.010.
22. . W. Wang, C. Xu, Y. Zhang, Y. Zhou, S. Meng, Y. Deng, An improved ultrasonic method for plane stress measurement using critically refracted longitudinal waves, NDT & E International 99 (2018) 117-122, https://doi.org/10.1016/j.ndteint.2018.07.006
23. . H. Liu, Y. Li, T. Li, X. Zhang, X. Zhang, Y. Liu, K. Liu, Y. Wang, Influence factors analysis and accuracy improvement for stress measurement using ultrasonic longitudinal critically refracted (LCR) wave, Applied Acoustics 141 (2018) 178-187, https://doi.org/10.1016/j.apacoust.2018.07.017.
Downloads
Published
Issue
Section
License
Copyright (c) 2023 Journal of Design Against Fatigue

This work is licensed under a Creative Commons Attribution 4.0 International License.