Heat Treatment of 440C Stainless Steel: Mechanical and Electrochemical Behaviour

Authors

  • Amirhossein Mahmoudi School of Engineering, University of West of England, Frenchay Campus, Bristol BS16 1QY, UK, Author
  • Nikunj Chavda 1-Renishaw PLC, Wotton-Under-Edge, GL12 8JR, UK, 2- School of Engineering, University of West of England, Frenchay Campus, Bristol BS16 1QY, UK, Author
  • Amir Zomorodian Renishaw PLC, Wotton-Under-Edge, GL12 8JR, UK Author

DOI:

https://doi.org/10.62676/jdaf.2025.3.2.20

Keywords:

440C stainless steel; heat treatment;, ; wear resistance; corrosion behaviour, cryogenic processing, tribology

Abstract

This study aims to evaluate the effects of different heat treatment routes on the microstructure, mechanical properties, corrosion resistance, and tribological performance of 440C stainless steel, with comparative analysis against 416 martensitic stainless steel. Scanning electron microscopy (SEM) was employed to examine microstructural changes, while hardness was measured using standard tests. Corrosion behaviour was assessed through potentiodynamic polarization and open circuit potential (OCP) measurements, tribological performance via pin-on-disk tests, and mechanical properties using plastometry. Three heat treatment routes were investigated: double air tempering at 180°C after austenitising and air quenching, double vacuum tempering at 180°C, and nitrogen tempering at 180°C followed by cryogenic quenching and subsequent nitrogen tempering. Results indicate that all heat treatments significantly improve the mechanical properties of 440C stainless steel compared to untreated and heat-treated 416 stainless steel. Cryogenic treatment notably enhances both hardness and corrosion resistance more effectively than other methods, although its tribological performance under higher loads (15N) is inferior. These findings underscore the importance of tailoring heat treatment strategies to optimize 440C stainless steel for applications requiring high mechanical strength and corrosion resistance.

References

[1] Baker I. Fifty Materials That Make the World. https://doi.org/10.1007/978-3-319-78766-4

[2] Bush R, Gill J, Teakell J. Heat Treatment Optimization and Fabrication of a 440C Stainless Steel Knife. JOM. 2016;68:3167-73. https://doi.org/10.1007/s11837-016-2117-5

[3] Rodríguez VM, Nadimpalli VK, Pedersen DB, Ruiz A. Nondestructive evaluation of tempering treatment in a spray-formed 440C martensitic stainless steel using thermoelectric power measurements. MRS Advances. 2025;10:108-14. https://doi.org/10.1557/s43580-024-01060-3

[4] Granta A. Stainless steel, martensitic, AISI 440C, tempered at 316°C. Granta 2024R2.

[5] Syarif J, H. Yousuf M, Sajuri Z, Baghdadi AH, Merabtene M, Omar MZ. Effect of Partial Solution Treatment Temperature on Microstructure and Tensile Properties of 440C Martensitic Stainless Steel. Metals2020. https://doi.org/10.3390/met10050694

[6] Rodríguez Herrejon V, Ruiz A, Bedolla-Jacuinde A, Nadimpalli VK. Comparative Analysis of Wear Properties of 440C Tool Steel Fabricated by Spray Forming and Conventional Casting. Journal of Materials Engineering and Performance. 2025. https://doi.org/10.1007/s11665-025-11860-9

[7] Idayan A, Gnanavelbabu A, Rajkumar K. Influence of Deep Cryogenic Treatment on the Mechanical Properties of AISI 440C Bearing Steel. Procedia Engineering. 2014;97:1683-91. https://doi.org/10.1016/j.proeng.2014.12.319

[8] Hetzner DW, Van Geertruyden W. Crystallography and metallography of carbides in high alloy steels. Materials Characterization. 2008;59:825-41. https://doi.org/10.1016/j.matchar.2007.07.005

[9] Yang J, Yu T, Wang C. Martensitic transformations in AISI 440C stainless steel. Materials Science and Engineering: A. 2006;438:276-80. https://doi.org/10.1016/j.msea.2006.02.098

[10] Syarif J, H. Yousuf M, Sajuri Z, Baghdadi AH, Merabtene M, Omar MZ. Effect of Partial Solution Treatment Temperature on Microstructure and Tensile Properties of 440C Martensitic Stainless Steel. Metals. 2020;10:694. https://doi.org/10.3390/met10050694

[11] Rodríguez VM, López-Morelos VH, Nadimpalli VK, Bue Pedersen D, Ruiz A, Somers MA. Effect of Heat Treatment Processes on the Microstructure and Mechanical Properties of Spray‐Formed 440C Martensitic Stainless Steel. steel research international. 2023;94:2200749. https://doi.org/10.1002/srin.202200749

[12] Deng B, Yang D, Wang G, Hou Z, Yi H. Effects of Austenitizing Temperature on Tensile and Impact Properties of a Martensitic Stainless Steel Containing Metastable Retained Austenite. Materials. 2021;14:1000. https://doi.org/10.3390/ma14041000

[13] Campbell JE, Gaiser-Porter M, Gu W, Ooi S, Burley M, Dean J, et al. Indentation plastometry of very hard metals. Advanced Engineering Materials. 2022;24:2101398. https://doi.org/10.1002/adem.202101398

[14] Li X, Cui L, Li J, Chen Y, Han W, Shonkwiler S, et al. Automation of intercept method for grain size measurement: A topological skeleton approach. Materials & Design. 2022;224:111358. https://doi.org/10.1016/j.matdes.2022.111358

[15] Yang Z, Liu Z, Liang J, Yang Z, Sheng G. Elucidating the role of secondary cryogenic treatment on mechanical properties of a martensitic ultra-high strength stainless steel. Materials Characterization. 2021;178:111277. https://doi.org/10.1016/j.matchar.2021.111277

[16] Kara F, Çiçek AÃi, Demir H. Effect of Deep Cryogenic Treatment on Microstructure, Mechanical Properties, and Residual Stress of AISI 52100 Bearing Steel. Engineered Science. 2023;26:960. https://doi.org/10.30919/es960

[17] Brunatto SF, Cardoso RP, Santos LL. Behavior of Retained Austenite and Carbide Phases in AISI 440C Martensitic Stainless Steel under Cavitation. Eng2024. p. 1980-94. https://doi.org/10.3390/eng5030105

[18] Krishna SC, Tharian KT, Chakravarthi KVA, Jha AK, Pant B. Heat Treatment and Thermo-Mechanical Treatment to Modify Carbide Banding in AISI 440C Steel: A Case Study. Metallography, Microstructure, and Analysis. 2016;5:108-15. https://doi.org/10.1007/s13632-016-0266-0

[19] Liu B-b, Zhang H, Xu X-y, Tian Q-r, Fu J-x. Analysis of Cracking Causes of AISI 416 Martensitic Stainless Steel During Hot Rolling. Transactions of the Indian Institute of Metals. 2023;76:2643-50. https://doi.org/10.1007/s12666-023-02942-0

[20] Krishna SC, Tharian KT, Chakravarthi K, Jha AK, Pant B. Heat treatment and thermo-mechanical treatment to modify carbide banding in AISI 440C steel: a case study. Metallography, Microstructure, and Analysis. 2016;5:108-15. https://doi.org/10.1007/s13632-016-0266-0

[21] Iakovakis E, Avcu E, Roy MJ, Gee M, Matthews A. Wear resistance of an additively manufactured high-carbon martensitic stainless steel. Scientific Reports. 2022;12:12554. https://doi.org/10.1038/s41598-022-15621-9

[22] Todaka T, Shimizu K, Kusumoto K, Purba RH, Gaqi Y. Effect of Carbon Content on Three-body Abrasive Wear Characteristics of 28Cr-3Ni Cast Alloys. ISIJ International. 2021;61:2274-83. https://doi.org/10.2355/isijinternational.ISIJINT-2021-099

Downloads

Published

2025-11-09

How to Cite

Mahmoudi, A., Chavda, N., & Zomorodian, A. (2025). Heat Treatment of 440C Stainless Steel: Mechanical and Electrochemical Behaviour. Journal of Design Against Fatigue, 3(2). https://doi.org/10.62676/jdaf.2025.3.2.20