Mechanics of chip formation in Ultra-High Molecular Weight Polyethylene (UHMWPE)

Authors

  • H. Ghadbeigi The University of Sheffield, Faculty of Engineering (Sheffield), School of Mechanical, Aerospace and Civil Engineering Author
  • Luke Jones Author
  • Abdulrahman Hasan Author
  • Gemma Harling Author
  • Jack Rooke Author

DOI:

https://doi.org/10.62676/jdaf.2026.4.1.20

Keywords:

Orthogonal cutting; Chip formation; UHMWPE; In situ imaging; Viscoelastic recovery; Minimum uncut chip thickness, Orthpgonal cutting, Chip formation, UHMWPE, In situ imaging, Viscoelastic recovery

Abstract

Ultra-High Molecular Weight Polyethylene (UHMWPE) is widely used in medical and food applications but remains challenging to machine due to unstable chip formation, poor chip control, burr generation, and surface distortion. Chip formation mechanics in two grades of UHMWPE (medical-grade GUR 1050 and food-compliant PE1000) is investigated using a bespoke in situ orthogonal cutting rig and direct observation via high-speed imaging synchronised with force measurement. The influence of the uncut chip thickness on chip morphology and deformation behaviour was systematically examined. A gradually increasing uncut chip thickness revealed a sequence of rubbing, ploughing, mixed ploughing-shearing and shear-dominated continuous chip formation, with the crossover of the cutting and thrust forces marking the transition. The polymer grade had a profound effect on the formation of the chip within the primary and secondary deformation zones as well as the chip curvature: at similar uncut chip thickness the cutting forces of the two grades were comparable, whereas the thrust force of the medical grade was up to about 60% lower and its chip–tool contact length longer. With increasing uncut chip thickness, separation at the tool tip changed from shear to tearing ahead of the tool. The proposed methodology provides a robust platform for optimising cutting-edge geometries for improving chip control and reducing reliance on CO₂ cooling strategies, and for linking machining-induced surface deformation to the fatigue performance of UHMWPE components.

References

References

[1] M. C. Sobieraj, C. M. Rimnac, “Ultra high molecular weight polyethylene: mechanics, morphology, and clinical behavior,” Journal of the Mechanical Behavior of Biomedical Materials, vol. 2, no. 5, pp. 433–443, 2009, https://doi.org/10.1016/j.jmbbm.2008.12.006.

[2] A. G. Fisch, N. da Silveira Jr, N. S. Cardozo, A. R. Secchi, J. H. dos Santos, J. B. Soares, “Direct production of ultra-high molecular weight polyethylene with oriented crystalline microstructures,” Journal of Molecular Catalysis A: Chemical, vol. 366, pp. 74–83, 2013.

[3] E. N. Brown, R. B. Willms, G. T. Gray, P. J. Rae, C. M. Cady, K. S. Vecchio, J. Flowers, M. Y. Martinez, “Influence of molecular conformation on the constitutive response of polyethylene: a comparison of HDPE, UHMWPE, and PEX,” Experimental Mechanics, vol. 47, no. 3, pp. 381–393, 2007, https://doi.org/10.1007/s11340-007-9045-9.

[4] M. K. Musib, “A review of the history and role of UHMWPE as a component in total joint replacements,” International Journal of Biological Engineering, vol. 1, no. 1, pp. 6–10, 2012.

[5] Y. Kakinuma, S. Kidani, T. Aoyama, “Ultra-precision cryogenic machining of viscoelastic polymers,” CIRP Annals, vol. 61, no. 1, pp. 79–82, 2012, https://doi.org/10.1016/j.cirp.2012.03.039.

[6] M. Píška, K. Urbancová, “Advanced machining of joint implant UHMWPE inserts,” Machines, vol. 10, no. 11, Art. no. 1008, 2022, https://doi.org/10.3390/machines10111008.

[7] D. D. da Costa, H. L. Corrêa, C. J. Rebeyka, S. F. Zawadzki, “UHMWPE molecular structure analysis after turning operations and machinability with a standard off-the-shelf carbide tool,” Engineering Research Express, vol. 1, no. 2, Art. no. 025039, 2019.

[8] D. Axinte, Y. Guo, Z. Liao, A. J. Shih, R. M’Saoubi, N. Sugita, “Machining of biocompatible materials — recent advances,” CIRP Annals, vol. 68, no. 2, pp. 629–652, 2019, https://doi.org/10.1016/j.cirp.2019.05.003.

[9] J. W. Carr, C. Feger, “Ultraprecision machining of polymers,” Precision Engineering, vol. 15, no. 4, pp. 221–237, 1993, https://doi.org/10.1016/0141-6359(93)90105-J.

[10] K. Q. Xiao, L. C. Zhang, “The role of viscous deformation in the machining of polymers,” International Journal of Mechanical Sciences, vol. 44, pp. 2317–2336, 2002, https://doi.org/10.1016/S0020-7403(02)00178-9.

[11] B. Aldwell, R. Hanley, G. E. O’Donnell, “Characterising the machining of biomedical grade polymers,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol. 228, no. 10, pp. 1237–1251, 2014.

[12] J. Rooke, R. Bonnell, E. Pickford, A. Brown, D. Curtis, “Application of low frequency vibration to the turning of ultra-high molecular weight polyethylene,” Advanced Manufacturing: Polymer & Composites Science, vol. 11, no. 1, Art. no. 2449631, 2025, https://doi.org/10.1080/20550340.2025.2449631.

[13] B. Denkena, K. M. Heide, M.-E. Eggers, C. K. Emonde, C. Hurschler, “Analysis on micro-milling of UHMWPE for the integration of radiopaque markers on the surface of TKA inlays,” Production Engineering, vol. 20, no. 1, Art. no. 9, 2026, https://doi.org/10.1007/s11740-025-01401-7.

[14] R. Bertolini, A. Ghiotti, S. Bruschi, “Machinability of polyamide 6 under cryogenic cooling conditions,” Procedia Manufacturing, vol. 48, pp. 419–427, 2020.

[15] R. Bertolini, A. Ghiotti, S. Bruschi, “Cryogenic machining to enhance surface finish of a biomedical grade ultra-high-molecular weight polyethylene,” in Proceedings of ESAFORM 2021: 24th International Conference on Material Forming, Liège, Belgium, 2021, https://doi.org/10.25518/esaform21.3749.

[16] A. Siahsarani, S. Fattahi, A. Alinaghizadeh, B. Azarhoushang, R. Bösinger, “Data-driven optimization of processing parameters and cooling strategies in UHMWPE high speed milling through multi-criteria decision making using PCA and Pareto-based evolutionary algorithms,” International Journal of Precision Engineering and Manufacturing-Green Technology, vol. 13, no. 3, pp. 1099–1114, 2026, https://doi.org/10.1007/s40684-025-00836-8.

[17] F. P. Zaribaf, “Medical-grade ultra-high molecular weight polyethylene: past, current and future,” Materials Science and Technology, vol. 34, no. 16, pp. 1940–1953, 2018.

[18] M. Hussain, R. A. Naqvi, N. Abbas, S. M. Khan, S. Nawaz, A. Hussain, N. Zahra, M. W. Khalid, “Ultra-high-molecular-weight-polyethylene (UHMWPE) as a promising polymer material for biomedical applications: a concise review,” Polymers, vol. 12, no. 2, Art. no. 323, 2020, https://doi.org/10.3390/polym12020323.

[19] M. Hasegawa, S. Tone, Y. Naito, A. Sudo, “Ultra-high-molecular-weight polyethylene in hip and knee arthroplasties,” Materials, vol. 16, no. 6, Art. no. 2140, 2023, https://doi.org/10.3390/ma16062140.

[20] F. Ansari, B. Gludovatz, A. Kozak, R. O. Ritchie, L. A. Pruitt, “Notch fatigue of ultrahigh molecular weight polyethylene (UHMWPE) used in total joint replacements,” Journal of the Mechanical Behavior of Biomedical Materials, vol. 60, pp. 267–279, 2016, https://doi.org/10.1016/j.jmbbm.2016.02.014.

[21] J. Furmanski, M. J. Kraay, C. M. Rimnac, “Crack initiation in retrieved cross-linked highly cross-linked ultrahigh-molecular-weight polyethylene acetabular liners: an investigation of 9 cases,” The Journal of Arthroplasty, vol. 26, no. 5, pp. 796–801, 2011, https://doi.org/10.1016/j.arth.2010.07.016.

[22] A. G. Atkins, “Modelling metal cutting using modern ductile fracture mechanics: quantitative explanations for some longstanding problems,” International Journal of Mechanical Sciences, vol. 45, no. 2, pp. 373–396, 2003, https://doi.org/10.1016/S0020-7403(03)00040-7.

[23] D. J. Wyeth, A. G. Atkins, “Mixed mode fracture toughness as a separation parameter when cutting polymers,” Engineering Fracture Mechanics, vol. 76, no. 18, pp. 2690–2697, 2009, https://doi.org/10.1016/j.engfracmech.2009.07.023.

[24] S. Wojciechowski, “Estimation of minimum uncut chip thickness during precision and micro-machining processes of various materials—a critical review,” Materials, vol. 15, no. 1, Art. no. 59, 2022, https://doi.org/10.3390/ma15010059.

[25] B. R. K. Blackman, T. R. Hoult, Y. Patel, J. G. Williams, “Tool sharpness as a factor in machining tests to determine toughness,” Engineering Fracture Mechanics, vol. 101, pp. 47–58, 2013, https://doi.org/10.1016/j.engfracmech.2012.09.020.

[26] J. G. Williams, Y. Patel, B. R. K. Blackman, “A fracture mechanics analysis of cutting and machining,” Engineering Fracture Mechanics, vol. 77, no. 2, pp. 293–308, 2010, https://doi.org/10.1016/j.engfracmech.2009.06.011.

[27] Y. Patel, B. R. K. Blackman, J. G. Williams, “Determining fracture toughness from cutting tests on polymers,” Engineering Fracture Mechanics, vol. 76, no. 18, pp. 2711–2730, 2009.

[28] J. Furmanski, M. Anderson, S. Bal, A. S. Greenwald, D. Halley, B. Penenberg, M. Ries, L. Pruitt, “Clinical fracture of cross-linked UHMWPE acetabular liners,” Biomaterials, vol. 30, no. 29, pp. 5572–5582, 2009, https://doi.org/10.1016/j.biomaterials.2009.07.013.

[29] L. A. Pruitt, “Deformation, yielding, fracture and fatigue behaviour of conventional and highly cross-linked ultra high molecular weight polyethylene,” Biomaterials, vol. 26, no. 8, pp. 905–915, 2005, https://doi.org/10.1016/j.biomaterials.2004.03.022.

[30] D. Novovic, R. C. Dewes, D. K. Aspinwall, W. Voice, P. Bowen, “The effect of machined surface topography and integrity on fatigue life,” International Journal of Machine Tools and Manufacture, vol. 44, no. 2–3, pp. 125–134, 2004, https://doi.org/10.1016/j.ijmachtools.2003.10.018.

Downloads

Published

2026-10-31

Issue

Section

Articles

How to Cite

Ghadbeigi, H., Jones, L., Hasan, A., Harling, G., & Rooke, J. (2026). Mechanics of chip formation in Ultra-High Molecular Weight Polyethylene (UHMWPE). Journal of Design Against Fatigue, 4(1). https://doi.org/10.62676/jdaf.2026.4.1.20